|
|
|
Перечень доступного оборудования
|
|
The AAIB provides system announcement, ACD/UCD announcement, and User Greeting, along with a processor and DSP circuitry to support 8 simultaneous channels. To provide additional channels and/or storage capacity, up to three (3) VMIB or AAIBs may be installed in the iPECS-MG system with MPB300 for a maximum capacity of 24 channels. On an iPECS-MG system with MPB100, a maximum of two (2) VMIB or AAIBs can be supported for a maximum capacity of 16 channels.
|
ITEM
|
CHANNEL
|
SYSTEM GREETING/USER GREETING
|
|
VMIB
|
8
|
System Greeting (0.5hrs.), User Message (100 Hours)
|
|
AAIB
|
8
|
System Greeting (0.5hrs.), User Message (None)
|
AAIB can be installed on the universal slot No. 1-6 of any KSU except the MPB slot of 1st KSU. The maximum 3 AAIBs can be installed with MPB300 (MPB100: Max. 2 AAIBs)
NOTE:
1. If AAIB is installed on a System, voice prompt (Default=1-English, 2-3-Blank) should be uploaded for each country.
2. MP Software stores voice prompts on U8, Nand Flash of MPB100/MPB300 for each stored language (Korean, English, Italian, Russian, German, Danish, Hebrew, Spanish, Turkey and Swedish).
3. Voice prompt can be changed using the Web Admin, VMIB upgrade function.
LAN Specification
|
ITEM
|
SPECIFICATION
|
|
LAN
|
Interface 100 Base-T Ethernet (IEEE 802.3)
|
|
Speed
|
100 Mbps (Auto-Negotiation)
|
|
Duplex
|
Half Duplex or Full Duplex (Auto-Negotiation)
|
Pin Assignment
RJ45, LAN PORT
|
CONNECTOR
|
PIN NUMBER
|
NO
|
SIGNAL
NAME
|
FUNCTION
|
RJ45
|
 
|
4,5,7,8
|
RESERVED
|
|
1
|
TX+
|
Transmit Data
|
|
2
|
TX-
|
Transmit Data
|
|
3
|
RX-
|
Receive Data
|
|
6
|
RX+
|
Receive Data
|
Serial Port
|
CONNECTOR
|
PIN NUMBER
|
NO
|
SIGNAL NAME
|
Serial to
Audio Jack
|
|
1
|
Signal Ground
|
|
2
|
Receive Data
|
|
3
|
Transmit Data
|
|
4
|
Signal Ground
|
USB Port
|
CONNECTOR
|
PIN NUMBER
|
NO
|
SIGNAL NAME
|
USB
Type A
|
|
1
|
GND
|
|
2
|
D+
|
|
3
|
D-
|
|
4
|
VBUS (+5V)
|
Connectors, Switch and LED Functions
Connector and Switch Functions
CONNECTOR/
SWITCH
|
FUNCTION
|
REMARK
|
|
SW1
|
4-POLE Dip Switch (Function: not defined)
|
Default: Off
|
|
SW2
|
Battery back-up switch
|
Not Assembled at MP
|
|
SW3
|
Reset switch
|
|
|
SW4
|
Watch-dog Enable/ Disable (OFF: Enable, ON: Disable)
|
Not Assembled at MP
|
|
CN3
|
JTAG port for CPU emulator
|
For R&D Test
|
|
CN4
|
JTAG port for FPGA
|
For R&D only
|
LED Indication
|
LED
|
FUNCTION
|
REMARK
|
|
LD1
|
Normal operation indication (Activity Indication)
|
Blink (Blue Color)
|
|
LD2
|
Memory Full (ON – Full, OFF – Usable)
|
AAIB – Not used
|
|
LD3
|
Record (ON – Active, OFF – Idle)
|
|
|
LD4
|
Play (ON – Active, OFF – Idle)
|
|
|
MJ1-LD1 (Green/Orange)
|
ON – Link, Blink – Data Transfer
|
|
|
MJ1-LD2 (Yellow)
|
ON - 100Mbps, OFF – 10Mbps
|
|
|
|
|
